We're offline for a tune-up, we'll be up and running smoothly very soon. Show In the meantime, here are some other options available: Visit an Sign up for View us on Social Media We appreciate your patience – for your next visit: 15% offyour next purchase. Enter coupon code: in shopping cart. We look forward to serving you, Average rating for Rear brake pad replacement starstarstarstarstar 4.9 • based on 27 reviews of 26 businesses Why do Mazda CX-5 rear brake pads need to be replacement?The rear brakes on your Mazda CX-5 provide the stopping power when you put your foot on the brake pedal, as well as being used as the handbrake. They do wear out over time, depending on how much you use the brakes and will need to be replaced at some stage of your vehicle's life – and that’s where we come in handy! The average cost of having your rear brake pads replaced starts at around $150 all the way up to $400+, depending on the type of brake pads used. Mazda CX-5's with rear brake disc rotors will require rear brake pads. The brake pads are made of a composition that transfers heat while also holding up against the friction of being pushed up against the spinning brake rotor, to slow a vehicle down. Due to this friction, brake pads wear down and depending on brake pad composition some may wear down quicker than others, a good reason to purchase brake pad brands with a good reputation for delivering positive results. Another reason for increased Mazda CX-5 brake pad wear can be your driving style, remember to lift your foot off the brake pedal when you don't need to brake while driving, utilise gears to reduce speed when going down hills or gradually stopping and try to avoid sudden braking where possible. Brake pads should last between 25,000 to 80,000 km's, the reason why you can't put a specific time or distance travelled is due to the varying driving conditions. A delivery driver in the city will likely go through brakes quicker than a sales rep travelling on long stretches of country roads. This is outside the usual reporting cycle of our long-term Mazda CX-5 AWD Sport Diesel which is typically done each time it undergoes Preventive Maintenance Service or PMS, but this is a special occasion. It’s special because I happen to change the brake pads, and that’s the focus of this story. Truth be told, my brake pads weren’t due for replacement. The Mazda stock pads are pretty robust in terms of construction, and coupled with the fact that I’m pretty light on the pedal meant my pads were as thick as Mark Villar’s face. However, when Brembo’s official Philippine distributor, Auto Performance PH approached me to review their line of Premium Ceramic Brake Pads, there was only one choice. By default, the CX-5 was getting the Brembo treatment. With an SRP of P 9,250 for a set of both front and rear pads (for ordering info, you can reach them via Facebook Messenger), it’s not exactly cheap, but they do promise “low dust, low noise with longer wear and a positive brake pedal feel.” Basically, it’s everything you want in a set of pads. An added bonus is that the pads are colored red too—perfect if you want a racy look and feel peeking out of those 19-inch wheels. Now, I’ve driven about 120 kilometers or so on the new pads, but they’re mostly on the highway so Brembo says they’re not completely broken in (they recommend about 100 kilometers in stop-and-go traffic). Still, I’m happy to report that the brake pedal engagement does feel more progressive, and the bite, at least subjectively feels better compared to the stock pads. Whereas previously, the CX-5 needs to reach about half way through the brake pedal stroke to get decent bite in, these feel better about a fifth or a quarter of the way in. On the flip side, they do produce more dust now. As to how much more dust, we’ll see after they’ve been broken in and subjected to stop-and-go traffic. So, while my full feedback on the performance of the Brembo Premium Ceramic Pads is still up in the air, I can at least tell you about my installation experience. Mazda owners should read on because you’ll learn something new here. The pads were sent straight to the nearest Brembo authorized retailer and installer near my house, and that’s Vindicated Motorsports in Sto. Nino, Marikina. Owner Lawrence Makiramdam runs a small, tight operation that specializes in off-road rigs (he knows them like the back of his hand). Imagine his surprise though seeing a CX-5 approach the driveway of his shop. Before we start, Lawrence tells me that they typically need to bleed the brakes to accommodate the thicker Brembo Premium Ceramic pads. In the case of the CX-5 though, it came to everyone’s surprise that there was no need. The pads went straight in. It took less than 30 minutes to jack up the car, remove the stock pads, and install the new pads. No fuss, no drama. That said, we did encounter a bit of a problem towards the back of the CX-5, and this is a caveat to all Mazda owners out there rocking EPBs or Electronic Parking Brakes. Normally, replacing the rear pads require just jacking up the car, putting them on stands, and putting the hand brake down. In the case of the CX-5, and any other Mazda equipped with an EPB, it requires an additional step. In order to increase the clearance between the calipers to accommodate the new pads, Mazda EPBs have to be put in a service or maintenance mode. This must be done before taking the caliper apart. This is how to do it:
Once the pads have been replaced, the EPB remains in service or maintenance mode. So, this is how you exit it:
If done correctly, there’s no need to bleed the rear brakes because again, the Brembo pads fit straight in like they were OEM. Sadly, we didn’t realize it until we started taking the rear caliper assembly apart and the caliper wouldn’t clear the new pads. This necessitated us having to bleed the braking system. The entire system worked well, but to be sure, I had the EPB system re-checked by a Mazda service technician a week later. It required a EPB reset and recalibration which took an hour. It sounds like a bit of a hassle, but it was a learning experience for everyone concerned. It’s the result of vehicles having more and more standard tech put in, and it’s certainly something that’ll face car repair shops and car owners alike in
the future. How do you release the electric parking brake on a Mazda CXThe EPB can be released while the ignition is switched ON or the engine is running. When the EPB is released, the EPB indicator light and the EPB switch indicator light turn off. Securely depress the brake pedal and press down the EPB switch. Firmly depress the brake pedal and press the EPB switch.
How does Mazda electronic handbrake work?The EPB system applies the parking brake using an electric motor. The system can operate automatically and manually. The EPB switch indicator light turns on when applying the parking brake and it turns off when releasing the parking brake.
|