Check engine light and traction control light on jeep compass

Please wait while the page loads...

Is it safe to drive your 2014 Jeep Compass with the check engine light on?

If the check engine light is twinkling, this means that there is a important issue and it is recommended to service your Jeep Compass rapidly. This question is not very effortless because it any depends on the severity of the issue. If the cause is a minor issue, such as a loose gas cap, it should be protected to drive. This is commonly indicated by a steady glow of the check engine light. If you notice a variety in the performance of the vehicle, it could be an indication of a more critical problem. Call the experts at Courtesy Chrysler Jeep Dodge Ram by dialing 8136948784 so you can describe the issues. Or lower your speed and deliver your 2014 Jeep to our certified mechanics as soon as attainable.

What could cause the check engine light to come on in a 2014 Jeep Compass?

When your check engine light comes on, this could be as simple as tightening or replacing your gas cap. Likewise, the check engine light could also be a warning of a serious problem that could cause serious damage to your engine and come with a hefty repair bill. Depending on your make and model, the check engine light will illuminate or blink. A steady glow typically means something less serious but a flashing check engine light indicates that your vehicle’s engine is in serious trouble and service is needed immediately. If your check engine light is flashing in your 2014 Jeep Compass, we highly recommend not to drive the vehicle and schedule Jeep service today. Below is a list of the most common reasons your check engine light can come on:

  • Your catalytic converter is bad or going bad. The catalytic converter is a part of your 2014 Jeep Compass’s exhaust system. The catalytic converter's function is to turn the carbon monoxide created by the combustion process into carbon dioxide. A damaged catalytic converter is usually caused by neglected maintenance, which is why Courtesy Chrysler Jeep Dodge Ram offers a complimentary multi-point inspection with every Jeep service. If you have an issue with your catalytic converter and don't get it repaired, your 2014 Jeep Compass will not pass an emissions test, show a lack of engine performance and will negatively affect your fuel economy. Your car may run at a higher temperature, too, which can cause diversified problems from overheating.
  • Your 2014 Jeep Compass has a vacuum leak. Every Jeep Compass has a vacuum system that performs a advantageous variety of functions. The vacuum system also helps lower harmful emissions by routing the fumes as gasoline evaporates through the engine. If you notice that your RPM is high in idle or randomly surges, a vacuum leak could be the cause. Over time, vacuum hoses can dry out and crack, especially if they’re exposed to important heat or extreme freezing.
  • The battery is scanty or dead. The battery in you 2014 Jeep Compass every meaningful. Without a car battery, your car won’t start, light up the road ahead, play the radio or charge your phone. Today’s car batteries last much longer than they did some decades ago, and they don't certainly require maintenance. The price of a new one depends on the type of Jeep you drive, but check our actual service coupons and specials.
  • One of the most accomplished and copious cause is that your 2014 Jeep Compass gas cap is loose, damaged or missing. The gas cap for your 2014 Jeep Compass serves multiple purposes. It prevents gas fumes from being released when you aren't driving, it seals the fuel system and helps maintain pressure within the fuel tank. What happens if you have a bad fuel cap? If your gas cap is former or has a ruptured seal, you can lose fuel through evaporation which will result in more trips to the pump. Luckily, to replace a gas cap isn't expensive. If your check engine light turns on rapidly after you put gas in your 2014 Jeep Compass, first thing you should check is to make fearless the cap isn’t loose — or that it's still on your car’s roof or at the fuel pump.
  • New Spark Plugs or Plug Wires are mandatory for your 2014 Jeep Compass. The spark plugs are the part of your engine that ignites the air/fuel mixture in the combustion chamber of your vehicle. This explosion is what moves the pistons and makes the engine run. The spark plug wires deliver the spark from the ignition coil to the spark plugs. If you're spark plugs or spark plug wires are bad or former, you will experience poor performance and reduced power. In a little extreme cases, your engine will have trouble starting or continuing to run. Worn spark plugs and plug wires can cause clogged catalytic converter or damage to ignition coils and O2 sensors, first-rate to more expensive repairs.
  • Your mass airflow sensor (known as MAF) needs to be replaced. The mass airflow sensor in your Jeep Compass is what determines how much fuel is mandatory to run your engine efficiently by measuring the amount of air entering the engine. As a part of the engine management system, the mass airflow sensor helps adjust to convincing changes, like altitude. If your Jeep Compass is having trouble starting, idling rough or has a sudden change in the position of the throttle pedal, this could be a sign of a bad mass airflow sensor.
  • Issues with any aftermarket items. An aftermarket alarm, exhaust or diversified item can wreak havoc on your 2014 Jeep Compass if it’s not installed accurately. These aftermarket parts and accessories can drain the battery, trigger the check engine light, or even impede the vehicle from starting. If these issues sound natural, deliver your Compass to Jeep and have our team of certified mechanics ensure that your aftermarket items were installed correctly and aren't causing any issue. Getting accessories, especially aftermarket parts and accessories, or using OEM parts first place might cost a little bit more but could save you money from having to get poor work and damage caused by poor installation work corrected.
  • So what happens if I don’t replace your O2 sensor? A faulty sensor can not only affect your miles per gallon, but it can cause damage to your catalytic converter and your 2014 Jeep Compass's spark plugs. The O2 sensor sends data to the vehicle’s onboard computer to pick the prudent mixture of air and fuel that enters the cylinders in your engine. A bad O2 sensor can also cause a car to fail an emissions test.
  • Your O2 Sensor (Oxygen Sensor) needs to be replaced. The Oxygen sensor, known as the O2 sensor, measures the amount of oxygen in your exhaust system. If there is excess oxygen in your exhaust system, fuel burns faster and your vehicle will be less bargain when it comes to fuel economy.

What Does the Check Engine Light Mean?

One of the most commonly misunderstood lights or indicators in your 2014 Jeep Compass is the check engine light. The check engine light is part of the onboard diagnostics system, and displays in a few different ways. It can say "Check Engine", it can be a symbol of an engine, it can even be a combination of both. This light illuminates in either an amber or red color and is part of the diagnostics system found on your vehicle. Onboard computers increasingly have controlled and monitored vehicle performance since the 80s and do a variety of things for your 2014 Jeep Compass. Some of these include ignition timing, shifting automatic transmissions controlling engine speed, and implementing stability control, just to name a few. With that being said, the check engine light can mean a variety of different things. It can be as simple as your gas cap being loose or as serious as engine knocking. If your check engine light is on in your 2014 Jeep Compass, contact Courtesy Chrysler Jeep Dodge Ram. Contact Courtesy Chrysler Jeep Dodge Ram today! Our Jeep service department can assist you find out what code is turning your check engine light on or probe why your check engine light is flashing.

How much does it cost to get the engine light checked?

The average cost for a check engine light diagnosis & testing is typically between $88 and $111. The impartial news, Courtesy Chrysler Jeep Dodge Ram offers complimentary multi-point inspections and free diagnostics, in most cases, to assist indicate the cause of your check engine light. The check engine light warns of issues ranging from a gas cap that's not perfectly tightened to a more natural failure like a bad catalytic converter or a problem with one of the car's oxygen sensors, so it impartial to get the sufficient code reading and diagnosis.

2014 Jeep Compass Check Engine Light Codes

The check engine light turning on can be quite intimidating to see that little light on your vehicle’s dashboard suddenly illuminates, but in reality, it is not something that should cause you to shut down in fear right away. If you hear the term, diagnostic trouble codes (DTC), these are just another name for check engine light codes. These are automotive computer codes stored by the ECM, also known as the OBD (on-board computer diagnostic system) in your Compass. There are hundreds of different codes that your check engine light can represent. While that sounds daunting, with a little patience, tackling basic diagnostics will give you useful knowledge about your vehicle and will also allow that Check Engine Light to do what it is really supposed to do: be your guide. Unfortunately, obvious and helpful vehicle symptoms do not always accompany an illuminated Check Engine Light. Since there are hundreds of possible OBD codes, there are also hundreds of possible reasons for the light, including:

  • Computer output circuit issues
  • Bad Spark Plugs
  • O2 Sensor
  • Transmission issues
  • Fuel and air metering systems problems
  • Ignition system faults
  • Emissions controls issues
  • Loose Gas Cap or Missing Gas Cap
  • Old Battery

This is why it is important for someone who does not have a lot of automotive knowledge to not assume what a code means. If the engine light comes on due to a sincere concern, you risk damaging your car further by not repairing the issue right away. When your check engine light comes on, you should get it checked out rapidly by a certified Jeep mechanic. Call Courtesy Chrysler Jeep Dodge Ram at 8136948784 today or schedule your check engine light service online today!

2014 Jeep Compass Check Engine Light Flashing

Although there are countless potential causes of an illuminated Check Engine Light, we know from years of providing Check Engine Light Diagnosis Service that there are several common causes including something as simple as a loose gas cap. Other common reasons for a Check Engine Light are faulty emissions control part, a malfunction with the fuel injection system, dirty mass airflow sensor, damaged oxygen sensor, faulty head gasket, or defective spark plugs to name a few. No matter what is the root cause of the Check Engine Light, we have the Jeep Certified Technicians and the certified service protocol to isolate the root problem and repair it as needed to restore factory specifications. When this happens, the Check Engine Light turns off, and you can leave the service center knowing that your Jeep issue was fixed.

Every 2014 Jeep Compass was designed with a high-technology performance monitoring system with a computer, and a series of sensors positioned strategically throughout the vehicle on its crucial systems. The sensors are continually detecting conditions while sending data to the electronic control unit. If the electronic control unit detects that the data is out of factory specifications, the Check Engine Light illuminates telling you that there is a problem. However, that is the limitation of the Check Engine Light – it won’t tell you what exactly is wrong nor what to do about it. That’s where we come in; Courtesy Chrysler Jeep Dodge Ram provides a Check Engine Light Diagnosis Service that isolates the core problem and gives you a recommendation on what to do next from a Highly Qualified Service professional.

How many miles can you drive with the check engine light?

It could be anything from a bad sensor to plug wires needing to be replaced. If you check engine light is flashing, we imply that you pull over and contact Courtesy Chrysler Jeep Dodge Ram to help learn if your vehicle is safe to drive in or if we imply a tow truck. The safest bet is to decipher the code and then plan your strategy accordingly. Since each check engine code has its own level of severity, it is laborious to predict how many miles you can drive with the warning light on.

2014 Jeep Compass Check Engine Light

If the check engine light in your 2014 Jeep Compass starts flashing, that means that the problem needs speedy attention and your Jeep should be delivered in instantly. A flashing light indicates that the problem is sincere and if not taken care of instantly may result in premium damage to the vehicle. This blinking light usually indicates a severe engine misfire allowing unburned fuel to be dumped into the exhaust system. There it can quickly raise the temperature of the catalytic converter to a point where damage is likely, requiring an expensive repair. Some owners ask if spark plugs cause the check engine light to flash? This can absolutely be the cause. A bad, old or dirty spark plug can cause the engine to misfire. If your check engine light is flashing, please contact our unit of automotive experts at Courtesy Chrysler Jeep Dodge Ram promptly by calling 8136948784. If the problem is ignored or you continue to drive, this can spread to the spark plug wires, catalytic converter, or ignition coils which can lead to a very expensive repair.

Will the check engine light reset itself?

The check engine light on your 2014 Jeep Compass will usually shut itself off if the issue or code that caused it to turn on is fixed. For example, if the cause of your check engine light coming on was a loose gas cap, if it's tightened, the light will turn itself off. Likewise, if your catalytic converter is going functional, and you did a lot of stop-and-go driving, that may have turned on the check engine light due to the high usage of the converter. In most cases, your 2014 Jeep Compass light will go off after about 20-40 miles. If you drive over that amount and the light is still on, you will need to bring it in to Courtesy Chrysler Jeep Dodge Ram so the light and code can be double-checked and reset.

Check Engine Light Service 2014 Jeep Compass

What do you do when you’re driving along in your Jeep Compass and suddenly, a yellow light illuminates on your dash and says "Check Engine". If you’re like most Jeep owners, your heart sinks a little because you have little idea about what that light is trying to tell you or how you should react. The fear of the unknown (or the cost of the unknown) can be just as stressful. But take a deep breath and realize the light coming on doesn’t mean you have to pull the car over to the side of the road and call a tow truck, but it is recommended that you get your 2014 Jeep Compass checked as soon as possible. Ignoring that warning could end up causing major damage to expensive engine components.

When your 2014 Jeep Compass's ECM (electronic control module), which is the vehicle's onboard computer, finds a problem in the electronic control system that it can’t correct, a computer turns on your check engine light. This amber or yellow light is typically labeled “check engine” or “service engine soon”, or the light may be nothing more than a picture of an engine, or a picture of the engine with the word “check.”

When the light turns on, the ECM stores an engine code or “trouble code” in its memory that identifies as the issue, whether it's a sensor or a failing engine part. This code is read with an electronic scan tool that is used by our Jeep auto repair mechanics at Courtesy Chrysler Jeep Dodge Ram. There are also a number of relatively inexpensive code readers that are designed for do-it-yourselfers, should you choose that route too. While this code will tell you the issue that is detected, a true diagnosis still requires an experienced professional to determine the issue and repair it.

Why did my traction control and check engine light come on?

This light comes on when the computer has detected that something may be malfunctioning in the traction control system. The traction control system monitors the steering and stability of the vehicle and engages when loss of traction has been detected.

Why is my traction control light on Jeep Compass?

Common reasons for this to happen: ABS is malfunctioning: Traction control and ABS (anti-lock braking system) often share the same control module and internal self-diagnostics system. As a result, sometimes an issue in the ABS can trigger the traction control light.

Is it OK to drive with traction control light on?

While your car is typically safe to drive with the traction control light on, you should not drive it under certain conditions. If the traction control light, anti-lock braking system light, and red brake-warning light are on, your entire braking system may be affected.

Can low tire pressure cause the traction control light to come on?

The ABS or traction control system may be inadvertently activated by these false or inaccurate signals. Depending on the signal transmitted from the wheel speed sensors to the ABS system as a result of the change in tire pressure, this may have also caused the ABS light to come on.